Moscow-based TechnoPlast started to produce a unique ridge aerator

The engineering and manufacturing company TechnoPlast has developed and started production of a universal Pipe-cone ventilation element that has no analogues in the world. The company also holds a patent for the unique device.

"The Krovent Pipe-cone ridge aerator is a unique product in our product range. There are no analogues of this element in the world. Elements of similar purpose, which are present on the market, have a fixed installation angle. Ridge aerator Krovent Pipe-cone has the ability to adjust the angle of installation on the ridge from 70 to 120 ° C," - said the company's representative.

The Krovent Pipe-cone ridge ventilator is an efficient device capable of ventilating up to 60 square meters of the roof. Uniqueness, reliability and functionality of the development is confirmed by an international patent.

Product uniqueness

The ridge ventilator Krovent Pipe-cone is an effective device that can be installed at the highest point of the slope, therefore maintaining the maximum pressure difference between the points of air inlet and outlet. Also the deflector, which is mounted on the Pipe-cone, creates an additional draught. This enables the device to ventilate both gablets at the same time: the air leaves the ventilation gap in both directions without delay and in an almost straight line.

The Krovent Pipe-cone ridge ventilator is also a universal element as it can be used for any roof covering. In the case of a straight ridge, as with asphalt shingles - the aerator is installed directly on the ridge element. If the ridge is semi-circular or U-shaped, as is often the case with metal roofing tiles, the device is installed under the ridge capping. It is also possible to install the Aerator in roofs with different angles. In addition the Krovent Pipe-cone installation platform has vertical valleys that are designed to direct the water away in the desired direction.

About the development of the Pipe-cone

The development of the ridge ventilator Krovent Pipe-cone involved experts of the roofing market, whose experience has helped to create the most functional, high-quality and easy to install element.

After preparing all the drawings and layouts, TechnoPlast began to select the necessary raw materials. The main difficulty was that the cost of the product should not depend on foreign currency fluctuations, but at the same time it should be competitive with imported counterparts. After a careful selection, numerous laboratory tests and trials, TechnoPlast managed to find a raw material that meets all the parameters for the new product.

Functionality of Krovent Pipe-cone

The roof ventilation is an essential component of every roof covering.

The main function of the roof ventilation elements is the withdrawal of excess moisture from the roof: because of the difference in temperature inside and outside the premises in the roof condensate is formed, which, with poor ventilation settles on the insulation and wooden structures in the roof, leading to a sharp reduction in the life of the insulation, mold, rotting and disruption of the entire roof.

Roof ventilation also stabilizes the temperature of the roof: in the hot season, when the roofing material is sufficiently heated, roof ventilation does not allow this heat to heat the roofing pie itself, and in winter - does not heat the roof covering from the heat of the roofing pie.

The inlet of air is ensured through the eaves either through a soffit system or through a specially arranged gap directly into the ventilation duct. In turn, the air outlet is provided in the vicinity of the ridge of the building. Most often, the release of air occurs through point outlets - roof aerators.

About company

Engineering Production Company "TechnoPlast", founded in 2012, produces roof ventilation and sidewall canopies. At the moment the company is one of the leaders of the Russian market - ventilation elements Krovent familiar to consumers in all regions of Russia, as well as in the CIS countries and Europe.

Initially, the author of the idea was Vadim Smirnov, who to this day is the CEO of the company and at the same time the main author of the entire product line.

All the products in the Tekhno Plast range are developed by Russian engineers and are manufactured in Russia. The production itself is located in the Ruzsky urban district of the Moscow region. The company's location is logistically advantageous for both Russian and foreign partner companies.

Currently TechnoPlast is engaged in full cycle production. The company owns a park of injection molding machines and 48 molding forms. Every year new products are added to the company's assortment and, correspondingly, the number of necessary molds expands.